> ## Content Index
> Fetch the complete content index at: https://routerhaven.com/llms.txt
> Use this file to discover other available public pages before exploring further.

# Ethernet Cable Diagram: Wire Colors, Pinout, How to Read It
- URL: https://routerhaven.com/ethernet-cable-diagram/
- Published: 2026-11-18T02:00:00.000Z
- Updated: 2026-11-18T02:00:00.000Z
- Author: Caleb Renwick
- Tags: Networking

An [ethernet cable diagram shows](https://routerhaven.com/ethernet-cable-how-it-works/) which wire color goes to which pin inside an RJ45 plug. If you have a loose connector, it tells you how to place the eight conductors before crimping so the cable works in a router, switch, or wall jack. The main thing to get right is orientation, because the same plug looks different from the front, the back, or the wall jack.

## What an ethernet cable diagram is actually showing

An [ethernet cable diagram is a map](https://routerhaven.com/ethernet-switch/) between the eight small conductors inside the cable and the eight metal contacts, or pins, in an RJ45 plug. It usually shows two things at once: the pin number and the wire color assigned to that pin.

The same connector can look different depending on what you are looking at. If you look at the plug from the front, you see the contacts. If you look from the back, where the cable enters, you see the wire colors. If you look at a wall jack, you may be seeing the punchdown side of the same wiring standard, not the plug itself.

That is why one person can say a cable is wired correctly while another says the diagram looks upside down. They may both be looking at the same cable from different sides. The standard matters, but so does the orientation of the drawing.

For example, if you are wiring a loose RJ45 plug by hand, the diagram is only useful if you match it to the same side of the connector that the drawing shows. A correct color order on the wrong face of the plug still gives you a bad cable.

## The two wiring standards you’ll see: T568A and T568B

There are two common wiring standards for ethernet patch cables: T568A and T568B. They use the same RJ45 connector and the same eight pins, but the wire colors land on different pins.

Here they are side by side, from pin 1 to pin 8:

| Pin | T568A        | T568B        |
| --- | ------------ | ------------ |
| 1   | white/green  | white/orange |
| 2   | green        | orange       |
| 3   | white/orange | white/green  |
| 4   | blue         | blue         |
| 5   | white/blue   | white/blue   |
| 6   | orange       | green        |
| 7   | white/brown  | white/brown  |
| 8   | brown        | brown        |

The connector is the same either way. The diagram only changes because the color order changes. For a straight patch cable, the important thing is consistency: if both ends are wired the same way, the cable is straight-through.

T568B is common in many office and home installs, but T568A is also valid. The key point is not that one is “better,” but that the cable matches the jacks and patch panels around it. If a system already uses one standard, stick with that standard at every termination unless you have a specific reason not to.

The same diagram can be drawn two ways because the plug can be shown from the contact side or the wire-entry side. The pin numbers do not change, but the left-to-right appearance does. That is the source of a lot of confusion, especially when someone compares a plug diagram to a wall-jack diagram and expects the colors to line up the same way on the page.

![Two RJ45 ethernet cable plugs are shown with their wire colors arranged for wiring comparison.](https://tse1.mm.bing.net/th?q=RJ45%20ethernet%20cable%20plugs%20with%20colored%20wires&w=624&h=352&c=7)

## How to read the pin numbers without getting flipped around

The easiest way to avoid confusion is to decide which side of the plug you are looking at before you start counting. The pin numbers are the same no matter what, but your view changes the left-to-right order you see on the page.

For an RJ45 plug, hold it with the clip away from you and the gold contacts facing up. In that view, pin 1 is on the left and pin 8 is on the right. That is the most common way diagrams are drawn when they show the front of the plug.

If the clip is facing toward you, the image is mirrored from left to right. That is where people get mixed up and crimp a cable backward. A diagram that looks correct in one orientation can be wrong if you flip the connector in your hand without adjusting how you read it.

A good habit is this: first identify the clip, then identify whether you are looking at the contact side or the wire-entry side, then count pins from 1 to 8 based on that view. If the drawing does not say which side you are seeing, be cautious. The colors alone are not enough to orient the plug.

Pinout view for a standard RJ45 plug, with the clip away from you and the contacts facing up:

1. Pin 1: white/orange in T568B, white/green in T568A
2. Pin 2: orange in T568B, green in T568A
3. Pin 3: white/green in T568B, white/orange in T568A
4. Pin 4: blue
5. Pin 5: white/blue
6. Pin 6: green in T568B, orange in T568A
7. Pin 7: white/brown
8. Pin 8: brown

![A close-up shows the metal pins inside an RJ45 ethernet plug.](https://tse1.mm.bing.net/th?q=close-up%20RJ45%20ethernet%20plug%20pins&w=624&h=352&c=7)

## Straight-through vs crossover: which diagram you need

For most home and office patch cables, you want a straight-through cable. That means both ends use the same wiring standard, either T568A on both ends or T568B on both ends. A straight-through cable is what you use between a computer and a switch, a router and a wall jack, or a switch and a patch panel in normal setups.

A crossover cable uses different standards on the two ends. Traditionally, one end is T568A and the other is T568B. That swaps the send and receive pairs. It used to matter when connecting like devices directly, such as switch to switch or computer to computer, without an uplink port or similar feature.

These days, many modern network devices auto-detect and adjust, so crossover cables matter less than they used to. But they can still matter with older gear, certain industrial equipment, and some specialized setups. If you are unsure, check the port behavior first. For ordinary router, switch, and wall-jack wiring, a straight-through cable is usually the correct choice.

If the cable is going from one room jack to a patch panel and then to a switch, keep the same standard at every point unless the installed infrastructure already follows a different one. Mixing standards accidentally is what causes a lot of wiring confusion.

If you need a crossover, use the diagram that puts T568A on one end and T568B on the other. If you need a straight-through cable, use the same diagram on both ends. That distinction still matters when older devices do not auto-negotiate the way newer ones do.

## A standard ethernet cable diagram for an RJ45 plug

Here is the standard pinout you can match against a real RJ45 plug. This is the basic reference most people mean when they ask for an ethernet cable diagram.

With the clip facing away from you and the contacts facing up, pin 1 is on the left and pin 8 is on the right.

1. Pin 1: white/orange in T568B, white/green in T568A
2. Pin 2: orange in T568B, green in T568A
3. Pin 3: white/green in T568B, white/orange in T568A
4. Pin 4: blue
5. Pin 5: white/blue
6. Pin 6: green in T568B, orange in T568A
7. Pin 7: white/brown
8. Pin 8: brown

A practical way to use the diagram is to line up the cable conductors in order before you insert them into the plug. Do not rely on color memory alone. The solid wires and the striped wires can be easy to mix up, especially if the jacket is cut back too far or the pairs have been untwisted.

If you are wiring a cable for the first time, keep the pair twists as close to the plug as you can. The order at the pins matters, and the twist pattern matters too. Both are part of getting a clean connection.

Say you are holding the loose plug and the wire bundle in your left hand. Lay the wires flat in the pin order your diagram shows, then check the clip orientation again before you crimp. That last check keeps you from reading the diagram one way and inserting the conductors the other way.

![A cut ethernet cable and an RJ45 connector are laid out on a table for wiring.](https://tse1.mm.bing.net/th?q=RJ45%20connector%20and%20cut%20cable%20ends&w=624&h=352&c=7)

## The mistakes that make a cable fail or act weird

The most common mistakes are simple, but they can waste a lot of time.

- Reversed pairs: two wires in the same pair land on the wrong pins. The cable may seem partly alive, but the link can fail or behave erratically.
- Split pairs: the wires are in the right pin positions individually, but the pairing is wrong. This often creates poor performance even if basic continuity looks okay.
- Too much untwisting: if you flatten the pairs too far before the plug, you weaken the cable’s noise resistance and can get unstable links.
- Wrong standard on one end: one end is T568A and the other is not what you expected, or the wall jack follows a different scheme than the patch cord.
- Assuming every ethernet diagram is identical: some drawings show the front of the plug, some show the back, and some show a jack or punchdown block instead of an RJ45 plug.

The symptoms depend on the mistake. A cable might not link at all, it might link at one speed and not another, or it might pass simple checks but still perform badly under load. If you are diagnosing a cable that “sort of works,” split pairs and poor pair integrity are worth checking, not just pin continuity.

Another common mistake is using a diagram for the wrong object. A wall jack punchdown chart is not the same thing as a plug pinout, even if both use T568A or T568B. The wiring standard can be the same while the drawing itself is showing a different side of the connection.

## How to check your cable against the diagram

The quickest check is a cable tester. Plug each end into the tester and compare the lights or display to the expected pin order. A correct straight-through cable should show each pin mapped cleanly to the same pin at the other end if the tester is set up for that style, or it should show the expected crossover pattern if that is what you built.

If you only have a continuity tester or a multimeter, check one conductor at a time and verify that pin 1 reaches pin 1 on the far end for a straight cable, pin 2 reaches pin 2, and so on through pin 8\. For a crossover cable, confirm that the swapped pins match the chosen standard at each end.

A correct reading should show no shorts between pins and no opens on any conductor. If the tester reports a split pair or miswire, stop trusting the cable until you find the bad termination. A cable can look neat outside and still be wrong inside the plug.

If the connector is already crimped and the wire order is off, it is usually faster to cut it off and re-terminate than to try to rescue a bad end. Match the physical plug to the diagram first, then verify it before you put the cable into service.

## Conclusion

If you are wiring or fixing a cable, start with the connector orientation, then choose T568A or T568B, and make both ends match the job. For most home setups, a straight-through cable wired consistently on both ends is the right answer. If the cable still misbehaves after you crimp it, check for reversed pairs, split pairs, and too much untwisting before you blame the device. A tester is the fastest way to confirm that the diagram and the real cable agree.

## Frequently Asked Questions

### Can I use T568A on one cable and T568B on another in the same house?

Yes. The cable standards can coexist, but it is easier to troubleshoot if the whole installation follows one standard. The important thing is to keep each cable terminated correctly and know which standard each end uses.

### Does pin 1 always mean the leftmost wire?

Only when you are holding the RJ45 plug in the standard orientation, with the clip away from you and the contacts facing up. Flip the plug around and left-to-right reverses.

### Do I still need a crossover cable?

Usually not for modern gear, because many devices auto-detect and adjust. It can still matter with older equipment or special direct connections, so it is worth checking the device manual if a direct link will not come up.