> ## Content Index
> Fetch the complete content index at: https://routerhaven.com/llms.txt
> Use this file to discover other available public pages before exploring further.

# /23 subnet mask explained: IPs and dotted-decimal mask
- URL: https://routerhaven.com/23-subnet-mask/
- Published: 2026-11-12T08:23:00.000Z
- Updated: 2026-11-12T08:23:00.000Z
- Author: Caleb Renwick
- Tags: Networking

A /[23 subnet means the](https://routerhaven.com/subnet-mask-network-boundaries/) first 23 bits of the IPv4 address belong to the network, and the remaining 9 bits are for hosts. In plain terms, that gives you 512 total IP addresses in the block, with 510 usable for devices after you reserve the network and broadcast addresses. If you see \`/23\` in a router, DHCP scope, or subnetting exercise, the dotted-decimal mask is \`255.255.254.0\`.

## What /23 actually means

CIDR notation tells you how many bits in the 32-bit IPv4 address are fixed for the network. With `/23`, 23 bits are network bits and 9 bits are host bits. That means all addresses in the block share the same first 23 bits, while the last 9 bits can vary.

For example, if you see `192.168.10.0/23`, the `/23` tells you the subnet is larger than a /24 and smaller than a /22\. A /24 leaves 8 bits for hosts, so a /23 gives you twice as many addresses as a /24\. The key idea is simple: fewer host bits means fewer addresses per subnet.

Say you are checking an address and want to know whether it belongs to a `/23` block. Start by finding the subnet mask and the block size, then match the address to the correct network boundary.

## How many IP addresses a /23 gives you

A /23 has 9 host bits, so the total number of IP addresses is 2^9 = 512\. That is the full size of the block, including the network address and the broadcast address.

For normal host assignment, you usually subtract those two special addresses. That leaves 510 usable host addresses. So if you are planning DHCP, static assignments, or a VLAN size, a /23 is a good fit when you need a little over 254 hosts but not as many as a /22 provides.

The quick rule is:

- Total addresses: 512
- Usable host addresses: 510

Do not confuse the total block size with the number you can hand out to devices. Those are not the same.

![A network router sits beside an open laptop on a desk.](https://tse1.mm.bing.net/th?q=network%20router%20beside%20laptop%20photo&w=624&h=352&c=7)

## What subnet mask /23 converts to

`/23` converts to the dotted-decimal subnet mask `255.255.254.0`.

Here is why the third octet changes by 2\. In binary, a /23 mask is:

```text
11111111.11111111.11111110.00000000
```

Binary mask

That means the third octet is `11111110`, which is 254 in decimal. Because the block size in that octet is `256 - 254 = 2`, the subnet increments by 2 in the third octet. So valid /23 network starts look like `192.168.0.0`, `192.168.2.0`, `192.168.4.0`, and so on.

That increment matters when you are checking whether an address belongs to a given /23 or when you [are planning adjacent subnets](https://routerhaven.com/subnet-mask-networking/).

![A network router is placed beside a printed network diagram on a table.](https://tse1.mm.bing.net/th?q=network%20router%20next%20to%20printed%20network%20diagram%20photo&w=624&h=352&c=7)

## What range of IPs belongs to a /23

Use a simple example like `192.168.10.0/23`. Because the block size is 2 in the third octet, this subnet spans two /24-sized ranges: `192.168.10.0` through `192.168.11.255`.

From that block:

- Network address: `192.168.10.0`
- Broadcast address: `192.168.11.255`
- Usable host range: `192.168.10.1` to `192.168.11.254`

If you start with an address that is not the network address, you first need to find which /23 block it belongs to. For example, `192.168.11.20/23` is still in the `192.168.10.0/23` subnet, because /23 networks move in steps of 2 in the third octet. The even-numbered third octet is the network boundary in this example.

A quick way to check the range is to identify the network address first, then the broadcast address, and use the numbers in between for usable hosts.

## When a /23 is the right size

A /23 makes sense when you need around 500 usable addresses and want one subnet instead of two separate /24s. A medium-sized office VLAN is a common fit, especially if you want to keep devices in one broadcast domain. It also works well for a lab network, a Wi-Fi segment with many clients, or a DHCP scope that needs room to grow.

It is often used when a /24 would be too tight. A /24 only gives you 254 usable addresses, which can run out quickly once you count printers, phones, access points, servers, and temporary devices. A /23 gives you more breathing room without jumping all the way to a /22.

That said, a bigger subnet is not always better. If you do not need the extra space, keeping subnets smaller can make addressing, troubleshooting, and segmentation easier.

## The mistakes people make with /23

The most common mistake is treating /23 like `255.255.255.0`. That mask is a /24, not a /23\. A /23 is `255.255.254.0`, and the difference changes the subnet boundary, the broadcast address, and the usable range.

Another common error is assuming the usable count is 512 because the subnet contains 512 total addresses. The usable count is 510, because the first address is the network address and the last is the broadcast address.

People also get tripped up by odd third octets. With a /23, subnet blocks start on even numbers in the third octet when the first two octets are the same. So `192.168.10.0/23` is valid as a block boundary only if `10` is the correct network start for that addressing plan; otherwise, the actual subnet may begin at `192.168.8.0/23` or `192.168.10.0/23` depending on the larger scheme. The safest habit is to find the block size first, then check the network boundary.

Finally, watch for overlapping subnets. Two /23s cannot overlap if they are meant to be separate networks. If they do, routing and DHCP issues usually follow.

![A network router is shown with several labeled Ethernet cables connected.](https://tse1.mm.bing.net/th?q=network%20router%20with%20labeled%20cables%20photo&w=624&h=352&c=7)

## Quick answers about /23 subnet masks

A /23 is bigger than a /24\. It has twice as many total addresses, and almost twice as many usable host addresses.

If you want to calculate it without memorizing, use the host-bit rule: IPv4 has 32 bits total, so `/23` leaves `32 - 23 = 9` host bits. Then `2^9 = 512` total addresses, and `512 - 2 = 510` usable addresses.

You can also remember the mask by octet patterns. A /24 is `255.255.255.0`. A /23 borrows one bit from that third octet, which turns the mask into `255.255.254.0` and makes the subnet size double in that octet.

If you are checking a specific address, the fastest method is to find the nearest even third octet and use that as the /23 network boundary.

## Conclusion

If you see \`/23\`, read it as a subnet with 23 network bits, 9 host bits, \`255.255.254.0\` as the mask, and 510 usable IP addresses. The block spans two /24s, so the network and broadcast addresses sit at the ends of that two-octet range. Before you configure anything, confirm the network start, the broadcast address, and where the usable range begins and ends. That avoids the most common setup mistakes.

## Frequently Asked Questions

### Is /23 bigger than /24?

Yes. A /23 is bigger than a /24 because it contains 512 total addresses instead of 256, and 510 usable hosts instead of 254.

### What is the subnet mask for /23?

The subnet mask is \`255.255.254.0\`.

### How many usable hosts are in a /23?

There are 510 usable host addresses.

### How do I find the network range for a /23?

Use a block size of 2 in the third octet. The subnet spans from the network address to the broadcast address across two adjacent /24 ranges.